Categories

Total of 8 Items
Sort By
Conveyor Protections

PL10-2D Run Off Switches

Conveyor Protections

PL10-2D Run Off Switches

The PL10-2D Run Off Switch detects conveyor belt misalignment; two microswitches can trigger an alarm or conveyor shutdown to protect the conveyor belt from damage when belt drift occurs. When the belt runs off center, the roller arm will be deflected from its normal vertical position and at a preset angle activates the first microswitch which can output to an alarm. When the belt further displaces the roller arm by a preset angle, the second microswitch will be trigged to shut down the conveyor before damage can occur to the belt or plant. The PL10-2D run off switch is usually installed in pairs at both sides of the belt and positioned at a distance between 0.3m and 2m from the head pulley or tail pulley. Typically, it can be fastened at the top or bottom of the conveyor stringers with the actuating arm located 25mm to 75mm away from the outside edge of the belt.
Conveyor Protections

PL20 Safety Pull Switches

Conveyor Protections

PL20 Safety Pull Switches

The Safety Pull Switch is mounted on or alongside the conveyor stringer, with one end of the pull wire fastened to a fixed post and the other end fixed on to the actuator arm. The pull wire is supported by standoff eyebolts every 3m. The distance between the switch and fixed post should not exceed 24m. The spacing between two switches should be no more than 48m. When the actuator arm displaces (rotates) to the alarm position by force acting on the pull-wire, the microswitch is activated and interlocked until reset manually. The standard switch is protected to IP65, suitable for both indoor and outdoor installation. Where the optional nickel plated housing is specified, it can be used in acid, alkaline or salty environments. The nickel plated surface is well suited for highly corrosive application.
Conveyor Protections

PL50 Belt Damage Detector

Conveyor Protections

PL50 Belt Damage Detector

PL50 Damaged Belt Detector warns supervisory personnel of impending belt failures due to rips, punctures, splice failures, or sharp objects protruding through the belt fabric. Belt Damage Detectors mount in pairs positioned on either side of the belt. The units are connected by two spans of aircraft cable. One end of the cable mounts permanently to a support bracket and the other connects to a spring-loaded ball located in the unit. The cables loop underneath the belt from each side crossing at the midpoint. A belt problem is detected when an object or a piece of damaged belt hangs below the belt's surface and sweeps away one or both cables. As the cable is detached, it pulls a spring-loaded ball out of a socket, causing two micro switches to sound an alarm or to shut down the conveyor.
Conveyor Protections

PL40 Position Switches

Conveyor Protections

PL40 Position Switches

Series PL position switches are utilized to monitor the position of heavy moving machinery such as a crane or skip. When the actuator roller is displaced, the switch is triggered by an arm; the microswitch inside then activates and signals a shut off to stop the moving machinery.
Conveyor Protections

Tilt Switch Probe - Model SL20

Conveyor Protections

Tilt Switch Probe - Model SL20

When material rises to tilt the probe 15°or more from its vertical position, the internal steel ball rolls off center and its normally closed contacts will open. As material falls away from the probe body and the probe becomes upright, the ball returns to its original centered position, once again causing switch actuation with the contact closed. The change in the internal switch status is user accessible for signaling alarms or lights with the aim of safety protection.
Conveyor Protections

Tilt SWitch Controller - Model SL50

Saimo tilt switch controller is offered in two versions: SL28 for metal construction and SL29 for plastic construction. Both are protected to IP65, with large indicating lights located on the front panel. A 0-10 second adjustable time delay circuit in the control unit prevents momentary tilting of the switch from causing a false or premature contact transfer. A selectable jumper permits normal output condition for either vertical or tilted position of probe. Two normally-open and two normally-closed output contacts are available for connection to external alarms and/or controls.
Conveyor Protections

PL70 Motion Monitors

Conveyor Protections

PL70 Motion Monitors

The PL70 Motion Monitor is a microprocessor controlled speed monitoring device, sensing not only underspeed status but also overspeed and zero speed. The PL70 is comprised of four parts: controller, sensor, target, cam and mounting bracket. A standard NPN or other proximity type sensor compatible with the PL70 can be utilized; these sensors emit a serial of pulses representing speed. The PL70 Controller has two DPDT contact alarm outputs and an optional 4~20mA output so that programmed output functions can be made to monitor the equipment conditions.
Conveyor Protections

PL60 Under Speed Switches

Conveyor Protections

PL60 Under Speed Switches

The PL60 Under Speed Switch provides low-cost, reliable and a simple means of monitoring the rotational velocity of a shaft or other rotating equipment. When the belt speed or rotating speed slows down within the preset range, the PL60 switch outputs a signal for either alarm or shut down. This switch is housed in a weatherproof, hermetically sealed anti-corrosive enclosure, designed for exposure to harsh environments.
Currently Viewing 8 OF 8 ITEMS